View TS521507_4131541.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TS5215
300mA Low Noise LDO Voltage Regulator with Enable
SOT-25
Pin Definition: 1. Input 2. Ground 3. Enable 4. Bypass / Adjust 5. Output
SOT-89-5L
Pin Definition: 1. Bypass / Adjust 2. Ground 3. Enable 4. Input 5. Output
SOP-8
Pin Definition: 1. Enable 2. Input 3. Output 4. Bypass / Adj
8. Ground 7. Ground 6. Ground 5. Ground
General Description
TS5215 is an efficient linear voltage regulator with ultra low noise output, very low dropout voltage (typically 17mV at light loads and 300mV at 300mA), and very low power consumption (125uA at 100uA), providing high output current even when the application requires very low dropout voltage. The Chip Enable (EN) includes a CMOS or TTL compatible input allows the output to be turned off to prolong battery life. When shutdown, power consumption drops nearly to zero. TS5215 is included a precision voltage reference, error correction circuit, a current limited output driver, over temperature shutdown, revered battery protection and a reference bypass pin to improve its already excellent lownoise performance.
Features
Ultra Low Noise Output Output Current up to 350mA Low Dropout Voltage Low Power Consumption "Zero" Off-mode Current Logic Controlled Electronic Enable Internal Current Limit Thermal Shutdown Protection Cellular Telephones Palmtops, Notebook Computers Battery Powered Equipment Consumer and Personal Electronics SMPS Post Regulator and DC to DC Modules High-efficiency Linear Power Supplies Portable Application
Typical Application Circuit
TS5215CX5xx VIN VOUT COUT 2.2uF CBYP 470pF
EN on off
Application
TS5215CX5 VIN R1 EN COUT 2.2uF CBYP 470pF R2 VOUT
Ordering Information
Part No. Package Packing
off TS5215CX5xx RF SOT-25 3Kpcs / 7" Reel TS5215CY5xx RM SOT-89-5L 1Kpcs / 7" Reel TS5215CSxx RL SOP-8 2.5Kpcs / 13" Reel Note: Where xx denotes voltage option, available are 50=5.0V 33=3.3V 25=2.5V Leave blank for adjustable version. Contact factory for additional voltage options.
on
Adjustable Version: VOUT = 1.24 (R1+R2)/R2 (Adjustable output range up to 8V) EN (pin3) may be connected directly to VIN (pin 1) Low noise operation: CBYP =470pF, COUT >2.2uF Basic operation: CBYP =not used, COUT >2uF
1/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable
Absolute Maximum Rating (Note 1)
Parameter
Input Supply Voltage Enable Input Voltage Power Dissipation (Note 2) SOT-25 Thermal Resistance SOT-89-5L JA TJ TSTG SOP-8 Operating Junction Temperature Range Storage Temperature Range o Lead Soldering Temperature (260 C)
Symbol
VIN VCE PD
Limit
-20~ +20 -20~ +20 Internal limited 220 110 160 -40 ~ +125 -65 ~ +150 5
Unit
V V
o
C/W
o o
C C S
Recommend Operating Rating (Note 2)
Parameter
Input Supply Voltage Enable Input Voltage
Symbol
VIN VCE
Limit
+2.5 ~ +16 0 ~ VIN
Unit
V V
Electrical Specification (VIN =Vo+1V, Io=100uA, COUT=1uF, Vce2V, TJ = 25oC, unless otherwise specified.)
Parameter
Output Voltage Output Voltage Temp. Coefficient Line Regulation Load Regulation (Note 5)
Conditions
VIN=Vo + 1V (Note 4) Vo+1V VIN 16V 0.1mA Io 300mA Io=100uA Io=50mA Io=150mA Io=300mA Io=100uA
Min
0.98|Vo| ------------------2.0 ---
Typ
VOUT 40 0.005 0.02 40 150 220 300 80 350 600 1900 0.01 -400 75 0.05 260 --0.01 5
Max
1.02|Vo| -0.05 0.2 48 190 265 360 125 600 1500 2500 1 5 600 ---0.4 --1 20
Unit
V ppm/ C % %
o
Dropout Voltage (Note 6)
mV
Ground Pin Current (Note 7)
Io=50mA Io=150mA Io=300mA VIN <0.4V (Shutdown) VIN <0.18V (Shutdown) VOUT=0V At f=100Hz, Io=100uA, Io=50mA, COUT=2.2uF, Regulation shutdown Regulation enable VIL 0.4V VIH 2.0V
uA
Quiescent Current Output Current Limit Power Supply Rejection Ratio Thermal Regulation (Note 8) Output Noise
uA mA dB %/W nVHz V V uA
Enable Function
Enable Input Logic-Low Voltage Enable Input Logic-Low Voltage Enable input Current
2/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable
Electrical Specification (Continue)
Note: 1. Exceeding the absolute maximum rating may damage the device. 2. The maximum allowable power dissipation at any Ta is Pd(max) = [TJ(MAX) - Ta] + JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. 3. The device is not guaranteed to function outside its operating rating. 4, Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 5, Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 1mA to 300mA (5V version) and 1mA to 120mA (VOUT <5V version). Changes in output voltage due to heating effects are covered by the thermal regulation specification. 6, Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. 7, Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 8, Thermal regulation is defined as the change in output voltage at a time "t" after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 300mA load pulse at Vin=16V for t=10mS.
Block Diagrams
3/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable
Application Information
Enable Input
TS5215 series feature an active-high (>2V) enable (EN) input that allows ON/OFF control of the regulator. Current drain reduces to "zero" when the device is shutdown, with only micro-amperes of leakage current. The EN is compatible with CMOS logic interfacing. EN may be directly tied to VIN and pulled up to the maximum supply voltage.
Input Capacitor Requirement
An input capacitor of 0.1uF or greater is recommended when the device is more than 10" away from the bulk AC supply capacitance or when the supply is a battery.
Output Capacitor Requirement
The TS5215 series requires an output capacitor to maintain stability and improve transient response is necessary. 2.2uF minimum is recommended. Larger values improve the regulator's transient response. The output capacitor value may be increased without limit. The output capacitor should have an ESR (effective series resistance) less than 5 and a resonant frequency above 1MHz. Ultra low ESR capacitors can cause a low amplitude oscillation on the output and/or under damped transient response. Most of tantalum or aluminum electrolytic capacitors are adequate; film types will work. Since many o aluminum electrolytic have electrolytes that freeze at about -30 C, solid tantalums are recommended for operation o below -25 C. At lower values of output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.47uF for current below 10mA or 0.33uF for currents below 1mA.
Reference Bypass Capacitor
Bypass is connected to the internal voltage reference. A 470pF capacitor (CBYPASS) connected from Bypass to Ground quiets this reference, providing a significant reduction in output noise. CBYPASS reduces the regulator phase margin; when using CBYPASS, output capacitors of 2.2uF or greater are generally required to maintain stability. The star up speed of the TS5215 is inversely proportional to the size of the reference bypass capacitor. Applications requiring a slow ramp up of output voltage should consider larger values of CBYPASS. Likewise, if rapid turn on is necessary, consider omitting CBYPASS. If output noise is not a major concern, omitted CBYPASS and leave Bypass open.
No Load Stability
The TS5215 series will remain stable and in regulation with no load, unlike many other voltage regulators. This is especially important in CMOS RAM keep alive applications.
Adjustable Regulator Design
The adjustable regulator versions can be adjusted to a specific output voltage by using two external resistors to programming the output voltage anywhere between 1.25 and the 8V maximum operating rating of the family. Two resistors are used. Resistors can be quite large up to 470k, because of the very high input impedance and low bias current of the sense comparator, the resistor values are calculated by: A capacitor from Adjust to Ground provides greatly improved noise performance. TS5215CX5 VIN R1 EN off on CBYP 470pF R2 Adjustable Version: VOUT = 1.24 (R1+R2)/R2 (Adjustable output range up to 8V) VOUT COUT 2.2uF
4/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable
Application Information (Continue)
Dual Supply Operation
When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground.
Thermal Characteristics
TS5215 series is designed to provide 300mA (5V version) of continuous current in a very small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. To determine the maximum power dissipation of the package, use the junction-ambient thermal resistance of the device and the following basic equation: PD(MAX) = [ TJ(MAX) - TA ] /JA TJ(MAX) is the maximum junction temperature of the die(125 C), and Ta is the ambient operating temperature. JA is layout dependent, the actual power dissipation of the regulator circuit can be determined using the equation: PD = (VIN - VOUT) * IOUT + VIN * IGND Substituting Pd(max) for Pd and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the TS5215CX33 at room temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: o o o PD(MAX) = (125 C - 25 C) / 220 C/W PD(MAX) = 455mW The junction to ambient thermal resistance for the minimum footprint is 220 C/W, the maximum power dissipation must not be exceeded for proper operation. Using the output voltage of 3.3V and an output current of 120mA, the maximum input voltage can be determined. From the electrical characteristics table, the maximum ground current for 120mA output current is 2.5mA. 445mW = (VIN - 3.3V ) * 300mA + VIN * 2.5mA 445mW = VIN * 300mA - 3.3 * 300mA + VIN * 2.5mA 445mW = VIN * 300mA - 990mW + VIN * 2.5mA 1435mW = VIN * 302.5mA VIN (max) = 4.74V Therefore, a 3.3V application at 300mA of output current can accept a maximum input voltage of 4.74V in a SOT-25 package.
o o
Fixed Output Regulator Design
VIN TS5215CX5xx VOUT COUT 2.2uF CBYP 470pF TS5215CX5xx VIN VOUT COUT 2.2uF
EN off on
Ultra Low Noise Fixed Voltage Application
Includes a 470pF capacitor for low noise operation and shows EN connected to IN for an application where enable/shutdown is not required. COUT= 2.2uF minimum.
Low Noise Fixed Voltage Application
An example of a low noise configuration where bypass is not required. COUT= 2.2uF minimum
5/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable SOT-25 Mechanical Drawing
DIM A+A1 B C D E E H L 1 S1
SOT-25 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 0.09 1.25 0.0354 0.0492 0.30 0.50 0.0118 0.0197 0.09 0.25 0.0035 0.0098 2.70 3.10 0.1063 0.1220 1.40 1.80 0.0551 0.0709 1.90 BSC 0.0748 BSC 2.40 3.00 0.09449 0.1181 0.35 BSC 0.0138 BSC 0 10 0 10 0.95 BSC 0.0374 BSC
Marking Diagram
H = Device Code X = Voltage Code (5 = 5.0V, S = 3.3V, K = 2.5V) Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code
6/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable SOP-8 Mechanical Drawing
DIM A B C D F G K M P R
SOP-8 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 4.80 5.00 0.189 0.196 3.80 4.00 0.150 0.157 1.35 1.75 0.054 0.068 0.35 0.49 0.014 0.019 0.40 1.25 0.016 0.049 1.27BSC 0.05BSC 0.10 0.25 0.004 0.009 0 7 0 7 5.80 6.20 0.229 0.244 0.25 0.50 0.010 0.019
Marking Diagram
XX = Voltage Code (50 = 5.0V, 33 = 3.3V, 25 = 2.5V) Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code
7/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable SOT-89-5L Mechanical Drawing
DIM A B C D E F G H I J
SOT-89-5L DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 4.40 4.60 0.17 0.18 4.05 4.25 0.16 0.17 1.50 1.70 0.06 0.07 0.35 0.41 0.01 0.02 2.40 2.60 0.09 0.10 0.80 -0.03 -3.00(typ) 0.12(typ) 1.50(typ) 0.06(typ) 0.40 0.52 0.01 0.02 1.40 1.60 0.05 0.06
Marking Diagram
Y M = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code XX = Voltage Code (50 = 5.0V, 33 = 3.3V, 25 = 2.5V) = Package Code for Adjustable type (CY5 = SOT-89-5L)
8/9
Version: A07
TS5215
300mA Low Noise LDO Voltage Regulator with Enable
Notice
Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC's terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale.
9/9
Version: A07

▲Up To Search▲

Price & Availability of TS521507

	To Download TS521507 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .